{"title":"Copper tube terminals","description":"\u003cp\u003eTinned copper tube terminals from 6mm² to 120mm², in M6, M8, M10 and M12 stud sizes. Seamless copper barrel, electro-tin plated, with a bell mouth entry and an inspection hole so you can see the conductor is fully home before you crimp.\u003c\/p\u003e\u003cp\u003eThe hole size is on every option, because a lug that will not go over the stud is no use however good the crimp is. M6 takes a 6.4mm hole, M8 an 8.4mm, M10 a 10.5mm and M12 a 13mm.\u003c\/p\u003e\u003cp\u003eSold singly or in packs of ten. If you would rather we crimped them for you, the \u003ca href=\"\/pages\/configure\"\u003emade-to-measure configurator\u003c\/a\u003e does the cable, the crimp and the heat shrink in one go.\u003c\/p\u003e","products":[{"product_id":"copper-tube-terminal-6mm2","title":"Copper Tube Terminal 6mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 6mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 6mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M8 (8.4mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249096728956,"sku":"CC-LUG6-M8-1","price":0.72,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249096761724,"sku":"CC-LUG6-M8-10","price":6.12,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05101.jpg?v=1785879629"},{"product_id":"copper-tube-terminal-35mm2","title":"Copper Tube Terminal 35mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 35mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 35mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M8 (8.4mm hole), M10 (10.5mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249097875836,"sku":"CC-LUG35-M8-1","price":1.62,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249097908604,"sku":"CC-LUG35-M8-10","price":13.76,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249097941372,"sku":"CC-LUG35-M10-1","price":1.62,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249097974140,"sku":"CC-LUG35-M10-10","price":13.76,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05101_dd24a386-63d1-4f03-a7ac-f901b06a4802.jpg?v=1785879642"},{"product_id":"copper-tube-terminal-10mm2","title":"Copper Tube Terminal 10mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 10mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 10mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M6 (6.4mm hole), M8 (8.4mm hole), M10 (10.5mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M6 (6.4mm hole) \/ Single","offer_id":57249099186556,"sku":"CC-LUG10-M6-1","price":0.72,"currency_code":"GBP","in_stock":true},{"title":"M6 (6.4mm hole) \/ Pack of 10","offer_id":57249099219324,"sku":"CC-LUG10-M6-10","price":6.12,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249099252092,"sku":"CC-LUG10-M8-1","price":0.72,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249099284860,"sku":"CC-LUG10-M8-10","price":6.12,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249099317628,"sku":"CC-LUG10-M10-1","price":0.72,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249099350396,"sku":"CC-LUG10-M10-10","price":6.12,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05101_88f01b5a-e665-4c06-ba1f-aa294c2673e5.jpg?v=1785879661"},{"product_id":"copper-tube-terminal-16mm2","title":"Copper Tube Terminal 16mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 16mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 16mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M6 (6.4mm hole), M8 (8.4mm hole), M10 (10.5mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M6 (6.4mm hole) \/ Single","offer_id":57249101152636,"sku":"CC-LUG16-M6-1","price":0.9,"currency_code":"GBP","in_stock":true},{"title":"M6 (6.4mm hole) \/ Pack of 10","offer_id":57249101185404,"sku":"CC-LUG16-M6-10","price":7.66,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249101218172,"sku":"CC-LUG16-M8-1","price":0.9,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249101250940,"sku":"CC-LUG16-M8-10","price":7.66,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249101283708,"sku":"CC-LUG16-M10-1","price":0.9,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249101316476,"sku":"CC-LUG16-M10-10","price":7.66,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05101_3a43b3ab-bb26-4536-b147-84c30575288f.jpg?v=1785879693"},{"product_id":"copper-tube-terminal-25mm2","title":"Copper Tube Terminal 25mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 25mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 25mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M6 (6.4mm hole), M8 (8.4mm hole), M10 (10.5mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M6 (6.4mm hole) \/ Single","offer_id":57249102233980,"sku":"CC-LUG25-M6-1","price":1.26,"currency_code":"GBP","in_stock":true},{"title":"M6 (6.4mm hole) \/ Pack of 10","offer_id":57249102266748,"sku":"CC-LUG25-M6-10","price":10.7,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249102299516,"sku":"CC-LUG25-M8-1","price":1.26,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249102332284,"sku":"CC-LUG25-M8-10","price":10.7,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249102365052,"sku":"CC-LUG25-M10-1","price":1.26,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249102397820,"sku":"CC-LUG25-M10-10","price":10.7,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05101_6a58d42a-a639-4d59-808e-5e2d435312dd.jpg?v=1785879724"},{"product_id":"copper-tube-terminal-50mm2","title":"Copper Tube Terminal 50mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 50mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 50mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M8 (8.4mm hole), M10 (10.5mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249102856572,"sku":"CC-LUG50-M8-1","price":2.1,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249102889340,"sku":"CC-LUG50-M8-10","price":17.86,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249102922108,"sku":"CC-LUG50-M10-1","price":2.1,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249102954876,"sku":"CC-LUG50-M10-10","price":17.86,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05101_a825a8b4-70a1-400d-9467-faa05a8e930c.jpg?v=1785879777"},{"product_id":"copper-tube-terminal-70mm2","title":"Copper Tube Terminal 70mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 70mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 70mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M8 (8.4mm hole), M10 (10.5mm hole), M12 (13mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M8 (8.4mm hole) \/ Single","offer_id":57249104494972,"sku":"CC-LUG70-M8-1","price":3.3,"currency_code":"GBP","in_stock":true},{"title":"M8 (8.4mm hole) \/ Pack of 10","offer_id":57249104527740,"sku":"CC-LUG70-M8-10","price":28.06,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249104560508,"sku":"CC-LUG70-M10-1","price":3.3,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249104593276,"sku":"CC-LUG70-M10-10","price":28.06,"currency_code":"GBP","in_stock":true},{"title":"M12 (13mm hole) \/ Single","offer_id":57249104626044,"sku":"CC-LUG70-M12-1","price":3.54,"currency_code":"GBP","in_stock":true},{"title":"M12 (13mm hole) \/ Pack of 10","offer_id":57249104658812,"sku":"CC-LUG70-M12-10","price":30.08,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05161.jpg?v=1785879810"},{"product_id":"copper-tube-terminal-95mm2","title":"Copper Tube Terminal 95mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 95mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 95mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M10 (10.5mm hole), M12 (13mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249104691580,"sku":"CC-LUG95-M10-1","price":4.74,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249104724348,"sku":"CC-LUG95-M10-10","price":40.28,"currency_code":"GBP","in_stock":true},{"title":"M12 (13mm hole) \/ Single","offer_id":57249104757116,"sku":"CC-LUG95-M12-1","price":4.74,"currency_code":"GBP","in_stock":true},{"title":"M12 (13mm hole) \/ Pack of 10","offer_id":57249104789884,"sku":"CC-LUG95-M12-10","price":40.28,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05172.jpg?v=1785879838"},{"product_id":"copper-tube-terminal-120mm2","title":"Copper Tube Terminal 120mm² (Tinned)","description":"\u003cp\u003e\u003cstrong\u003eTinned copper tube terminal, 120mm².\u003c\/strong\u003e Seamless copper tube barrel, electro-tin plated, with a bell mouth entry and an inspection hole. The correct termination for flexible battery cable at this size.\u003c\/p\u003e\n\n\u003ch3\u003eSpecification\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody:\u003c\/strong\u003e seamless copper tube to BS EN 12449\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e bright electro-tin plating to BS 1872\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e type tested to BS EN IEC 61238-1-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable size:\u003c\/strong\u003e 120mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud sizes available:\u003c\/strong\u003e M10 (10.5mm hole)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBell mouth entry\u003c\/strong\u003e so the strands are not sheared at the barrel shoulder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection hole\u003c\/strong\u003e so you can confirm the conductor is fully home before you crimp\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNominal against actual hole size\u003c\/h3\u003e\n\u003cp\u003eThe stud size is the bolt it fits, not the hole diameter. An M6 lug has a 6.4mm hole, M8 is 8.4mm, M10 is 10.5mm and M12 is 13mm. Getting a lug that will not pass over a stud is the commonest complaint in this whole category, so we publish both.\u003c\/p\u003e\n\n\u003ch3\u003eCrimping\u003c\/h3\u003e\n\u003cp\u003eUse a \u003cstrong\u003ehexagonal\u003c\/strong\u003e die matched to the lug, not an indent crimp, and not a bolt cutter style tool. Hex applies force evenly from all sides and is standardised, so a DIN 22-series die works with a DIN 46235 lug from any manufacturer. Indent crimping is genuinely good on fine-stranded conductors but it is not standardised and it locks you to one maker's lugs.\u003c\/p\u003e\n\u003cp\u003eAt 70mm² and above, use two crimp positions along the barrel.\u003c\/p\u003e\n\u003cp\u003eDo not drill out a smaller lug to fit a larger stud. It removes palm material, weakens the joint and exposes bare copper. If the lug will not fit the terminal, you want either a different stud size or a reduced palm lug.\u003c\/p\u003e\n\n\u003ch3\u003eOr have us crimp it\u003c\/h3\u003e\n\u003cp\u003eEvery made-to-measure assembly we build is crimped on the bench with a hydraulic tool and a matched hex die, checked with a micrometer across the flats against the die maker's published figure, and measured end to end on a milliohm meter. You get the numbers on a certificate. \u003ca href=\"\/pages\/configurator\"\u003eConfigure an assembly\u003c\/a\u003e.\u003c\/p\u003e","brand":"Cut \u0026 Crimp","offers":[{"title":"M10 (10.5mm hole) \/ Single","offer_id":57249105019260,"sku":"CC-LUG120-M10-1","price":5.1,"currency_code":"GBP","in_stock":true},{"title":"M10 (10.5mm hole) \/ Pack of 10","offer_id":57249105052028,"sku":"CC-LUG120-M10-10","price":43.34,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/0164\/6204\/files\/8-05182.jpg?v=1785879860"}],"url":"https:\/\/cutandcrimp.co.uk\/collections\/copper-tube-terminals.oembed","provider":"Cut \u0026 Crimp","version":"1.0","type":"link"}